Clay Plaster-Base Coat

Only in White in colour.

Actual colour and texture will be related to actual light. Colour deviations cannot be excluded, each batch of product and aggregate accumulations may cause colour to vary slightly (It’s recommended to order amount required in one purchase). 實際色彩質感與光線有關。無法排除顏色所呈現色差，每一批產品和刷塗堆疊次數都會導致顏色略有差別（建議一次採購所需的量）。

• Natural Mineral Colour / 礦物原色

• Improve Air Quality / 淨化空氣

• Regulate Humidity / 調節濕度

• No Fading Problem / 永不褪色

• Reversible and Reuse / 重複使用

• Low Environmental Impact / 環境友善

Description: It is designed for the base coat of Clay Paint. Clay Plaster-Base Coat offers better humidity regulation than Designed Clay Plaster but less abrasion resistance, which may cause dusting problem over time if without any coating. For best results, it should be applied on a rough substrate (such as a cement-painted surface or apply mineral primer as a base coat if necessary), and paint with Clay Paint or Cellulose Primer as a coating after Clay Plaster actual dry. 描述 | 適用於粉刷款底塗；調濕效果非常佳，但與設計款比較相對不耐磨，且隨時間推移若沒有任何其他塗層保護則較容易會有掉粉的狀況，適合底塗；基材要求粗糙（例如水泥漆面，若有需要請使用市面上的礦物底漆進行打底），全乾後建議刷上粉刷款或修飾液以使表面更加牢固耐磨。

Application: Apply 1 coat is enough to feel the indoor environment quality become better (about 1mm thick). Apply 2 coats (about 2mm thick) can effectively regulate indoor humidity and improve air quality. Apply Clay Paint or Cellulose Primer to achieve a more durable finish surface. Applying with suitable tools can create a more beautiful texture. For interior use, do not continue splashed by water. It is always recommended to try it on a small area first! 應用 | 塗抹1層（約1mm厚）即可感覺到室内環境品質有所改善。塗抹2層（約2mm厚）泥土塗料可發揮極佳的調節室內濕度和提升空氣品質功能。全乾後，搭配粉刷款或修飾液以使表面更加牢固耐磨，可搭配其他工具創造更豐富的美感。適用室內，水不易持續潑灑處。永遠建議先小面積試做！

Types: Coarse particle sizes (0-1.3mm), matte and rough surface. 款式 | 粗顆粒（0-1.3mm），啞光粗糙面。

Storage: Keep in a dry and cool place. 保存 | 保存於陰涼處。

Installation Steps:

1. Check and prepare the subsurface in good condition (rough and clean). 診斷和確保施做基材狀況良好（應夠粗糙且乾淨）。

2. Pour out the precipitated water and stir Clay Plaster thoroughly by using mixing drill (continue for about 10 minutes). 倒出沉澱水分並用打泥器均勻攪拌（約連續十分鐘）。

3. Apply 1-2 coats by flexible trowel in a thin coat. Allow each coat to dry (about 1 day) before the next coat is applied. Install Mineral Primer if necessary before applying clay plaster to get a slightly rough surface so that it can adhere well to the substrate. 使用鏝刀（軟推刀）塗抹1～2層塗料，在塗抹新的一層時，請確保上一層已乾燥（約1天）。若有需要，請事先使用礦物底漆進行打底以便能使泥土塗料更好的附著在基材上。

4. Apply Cellulose Primer or Clay Paint by sponge (polish) or paintbrush (brush) to obtain a durable finished surface if necessary.若有需要可使用海綿（畫圈修飾）或刷子（刷塗）塗抹纖維素修飾液或粉刷款以獲得更牢固的表面。

5. Brush off the residual powder on the finished surface by paintbrush. 用毛刷清除表面殘留粉末。

Tools: Trowel, Mixing Drill, Plastering Hawk, Sponge or Paintbrush. 工具 | 鏝刀、水泥攪拌機、土帆、西德海綿或毛刷。